Geekcreit® 3.5 inch TFT LCD Touch Screen + Protective Case Support Cooling Fan + Touch Pen Kit For Raspberry Pi 3B+/3B/2B


29 in stock


29 in stock

Processing time: Ships in 36 hours. Shipping time: 15-35 business days depending on chosen shipping method (Tracked shipping)

Return Policy: 30-day refund or replacement 
You can return this product within 30 days after delivery to receive a replacement or a refund. 
Payment: PayPal & and all cards through PayPal checkout, Bank transfer (extra fees may apply, available after contacting support) 
Introduction :
Sometimes you use the the Raspberry Pi with 3.5 inch touchscreen , but sometime you don’t use them together. In this situation , you need a case which both suitable for Raspberry Pi alone or with 3.5 inch touchscreen. This is the reason we provide this new case — for  the people use 3.5 inch screen more convenient: When you use the touchscreen , just remove the cover board and fan; When you don’t use the touchscreen , you can use the cover and fan , which become a normal case.
Please note that you can’t use the 3.5 inch touchscreen and cooling fan at the sametime !

Features :
1. One case for two use :
​1). This case suport install 3.5 inch touchscreen , and need to remove the cover board and can’t use the fan in this using way.
2). When you don’t use the 3.5 inch touchscreen , it is a general case with cooling fan. 
2. Full access for Raspberry Pi : 
We leave every hole for SD card , HDMI , AV , Ethernet , USB , POE , Camera , MIPI DSI ports.
3. Support cooling fan :
You can install the cooling fan on the cover board , which make the best heat dissipation and extend the using life of Raspberry Pi.
( You can’t use the 3.5 inch touchscreen and cooling fan at the sametime ! )
4. Hange hole on the bottom :
We make 2 hole on the bottom so that you can hange the case on the wall or something else .
This design is very convenient when using the 3.5 inch touchscreen.
-480×320 pixel resolution, better display.
Driver   provided (works with custom Raspbian directly).
-Supports any revision of Rasp Pi (directly-pluggable).
-Designed for Raspberry Pi, an ideal alternative solution for monitor.
-Support software keyboard (system interaction without keyboard/mouse).
-Provides the best available protection/accessibility for Model B
Protect and secure your Rasp Pi from shocks, scratches and dust.
How to install the 3.5 inch touchscreen :
1). Install the Raspberry Pi on the base board 
2). ​Please stick the pad on  the back of 3.5 inch touchscreen , then insert the 3.5 inch touchscreen on Raspberry Pi by GPIO pin correctly ( don’t be malposed ) 
3). Install the cover board 


LCD Interface SPI
Touch Screen Type Resistive
Touch Screen Controller XPT2046
Colors 65536
Backlight LED
Resolution 320*480 (Pixel)
Aspect Ratio 8:5
Power Consumption TBD
Backlight Current TBD
Operating Temp. (Centigrade) TBD

Interface Definition:

1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16 NC NC
6, 9, 14, 20, 25 GND Ground
11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching
18 LCD_RS Instruction/Data Register selection
19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel
21 TP_SO SPI data output of Touch Panel
22 RST Reset
23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel
24 LCD_CS LCD chip selection, low active
26 TP_CS Touch Panel chip selection, low active

About the system of 3.5 touch screen

The touch screen need to configure the driver for touch function , otherwise you can not use it by your own system.
Here we provide the method to configure for Raspbian system :

Step 1: Download the Raspbian IMG  
Step 2: Burn the system image
If you don’t know how to do that,you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)

Drive File:

sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show

Make sure your RPI connects to the internet then wait a few minutes, when the system reboot ok, you can see that.

You can also download the system image which we already configured well by following links :

1. for Raspberry Pi 3 :

2. for Raspberry Pi 3 Modle B+ :

or refer to configure it by this link :

Package included:

1 x 3.5 inch Touch Screen
1 x Protective Case
1 x Touch Pen

Based on 0 reviews

0.0 overall

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.